Fixing up an old centreboard

More and more Australian Sailfish are surfacing as a result of the renewed interest in the class, and while some will require a full restoration, think Helen and Stanley Crocodile as shown in the Gallery, others might just require a bit of repair and maintenance to get back on the water.

A case in point, Mrs Vicious, winner of the very first National Titles held at Elwood in December/January 1968/69. Hull was in good shape even after years of storage, spars were sound, sail was good and needed only a few minor repairs. As a safety precaution, I replaced the stays as there was no way of knowing how sound they were, having been sailed in the ocean and then stored by the sea for well over ten years.

The centreboard on first inspection was a bit knocked about:

IMG_20170603_163407728

Apart from the chips along the trailing edge there were some dents and divots along the chord of the centreboard as well.

The first step is to sand it back so you can really see the condition. Now starts the good news, bad news stuff. Sanding back with a painted centreboard is relatively easy, as long as the base paint is sound as it is here, then there is no real concern about ruining the shape of the centreboard; as long as you are not sanding through the paint and into the wood, you can be sure you are safe, that’s the good news. However, in this case, sanding off the red paint revealed that this board had suffered some major damage and then been filled and faired to repair it.

IMG_20171208_113433998

Notice the amount of filler along the trailing edge at bottom left of the picture. The other side revealed more damage:

IMG_20171208_113421542

Again a lot of filling and fairing along the trailing edge, even more than I had suspected from the other side, also note the fairly deep scratch marks centre right of the photo below the handle.

OK, so here we are, the board is basically sound, even though there has been some damage, the paint is actually in really good shape, this is a win as it means the entire board doesn’t have to be taken back to bare wood (and filler).

The next step is to hand sand and fair the board, doing your best to remove the worst of any imperfections. If you have to take the centreboard back to bare wood, when it comes to painting I would suggest standing the board on its top end and painting or varnishing both sides of the blade at once to ensure there is no chance of distortion of the blade as one side dries while the other is still bare wood.

For this project I decided to use a roller with a short bristle, this was both a training exercise and an experiment for me, I usually use a brush, but if I am to move into the exciting world of epoxy resin I will have to develop my roller skills. As I hadn’t needed to take the board all the way back to bare wood I was able to paint one side of the board and then the other. Basically, apply paint, sand and fair, repeat until happy.

Two factors affected my paint choice. Firstly, availability, so I used the same paint that I had used to repaint Mrs Vicious’ hull, a well known semi gloss house paint. Which brings me to the second factor – if you are building a new boat, high gloss looks brilliant, really highlighting your boat, but that also means that when doing up an older boat it will highlight every bump, mark and imperfection, which is why I choose semi gloss, or even matt, paint or varnish for restoration work.

Here I did a total of four coats of paint, after the first coat I sanded back with 220 wet and dry (wet), repeated that after the second, after the third I sanded back with 400 wet and dry (wet) and then once I was sure I was happy with the fourth and final coat, I sanded back once again with 1200 wet, being sure to add just a drop of liquid detergent to the water to minimise the chances of scratching.

Here is the end result:

IMG_20171221_140358295

IMG_20171221_140416136

Is it perfect? Hell no, it’s a 50 year old centreboard that has had some rough times, but the shape has been cleaned up and the chips out of the back edge have been faired in, the scratches in the sides of the blade are smoothed out or removed and it is a clean, usable centreboard for many more years of use.

We hope that this will become part of an ongoing series on Repairs & Maintenance. If you are doing some fix up work on your Sailfish please send in some details and we can run a blog to help out others.

 

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s